HPP T5 HE ELECTRONIC BALLASTS

Features

  • Single chip controller with integrated digital power factor controller and digital ballast controller
  • Programmed preheat start
  • Filament heating cut off technology
  • Unity power factor with less than 5% THD
  • Constant light output with wider mains voltage range (156-265VAC)
  • Compatible with infrared control systems
  • Energy efficiency index (EEI) = A2
  • Mains over-voltage protection for 320VAC, 1 hour
  • Mains under-voltage protection
  • Open filament and over-current protection
  • EOL (asymmetric pulse test) and rectifying effect protection complied with latest IEC 61347-2-3 requirement
  • Automatic and instant restart by lamp exchange or upon restoration of mains voltage after under-voltage or over-
  • voltage conditions
  • Second restart attempt for latched faults , including EOL, rectifying effect, overload, capacitive modes, open filament and ignition timeout

Electrical Characteristics

Rated supply voltage 220 VAC ±10%
Supply frequency 50-60 Hz
Preheat time 1.5 Sec
Lumen factor 100%
Lamp current crest factor < 1.5
Ballast operating frequency >42 KHz
Operation life 90,000 Hrs
Lamp switching cycles 100,000
Ambient temperature (ta) -20 … +50°C

%

Power Factor

%

THD

Years Warranty

Hours of Life

Active Power Factor Correction

With the internal active harmonic filter, power factor of Hoye electronic ballasts is higher than 98% and total harmonic distortion is reduced to less than 10%, which is far beyond the limits of IEC 61000-3-2.

Electromagnetic Interference

The electromagnetic interference of Hoye electronic ballasts is further suppressed with the improved circuit design technologies. EMC performance is superior to most other products in the market.

Input Regulation

With the internal voltage regulation circuit, the luminous flux is unaffected by mains voltage. It provides a comfortable and stable light source for the environment.

Dimensions & Wiring

Compliances

EN 61347-2-1 Lamp controlgear. Particular requirements for starting devices (other than glow starters)

EN 61347-2-3 Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps

EN 60929 AC and/or DC-supplied electronic control gear for tubular fluorescent lamps – Performance requirements

EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

EN 61000-3-2 Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)

EN 61000-3-3 Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection

EN 61547 Equipment for general lighting purposes. EMC immunity requirements

Product Models

Model Lamp
Power
Circuit
Power (W)
Lamp
Power (W)
PF
(%)
THD
(%)
tc
(°C)
Weight
(g)
HPP-114 1x14W 16.5 1x13.7 98 4 65 220
HPP-121 1x21W 23.5 1x20.7 98 3 65 220
HPP-128 1x28W 31.0 1x27.8 98 2 65 220
HPP-135 1x35W 38.5 1x34.7 99 2 65 220
HPP-214 2x14W 31.0 2x13.7 98 2 65 315
HPP-221 2x21W 45.0 2x20.7 98 2 70 315
HPP-228 2x28W 60.0 2x27.8 99 2 70 315
HPP-235 2x35W 76.0 2x34.7 99 2 70 315